| Tool No. | description | Number | Picture |
| Combination Wrench 6-22, 24mm | 1 of each | |
| Combination wrench 8-19, 21mm Gearless or ratcheting. | 1 of each | |
| Flex-Head wrench 6-7, 8-9, 10-11, 12-13, 14-15, 16-17, 18-19mm | 1 of each | |
| Adjustable wrench 4" and 6" | 1 of each | |
| Allen wrench set (Ball end) 1,27→10 mm Note! Must include 7 mm | 1 | |
| Torx wrench set (Ball end), T9→T40 | 1 | |
| Ratchet 1/2"-drive
Ratchet 3/8"-drive | 1
1 | |
| Breaker bar 1/2"-drive | 1 | |
| Torque Wrenches 3/8"-drive 6-50Nm (with changeable head, ratchet, open ends, box ends)
Torque Wrenches 1/2"-drive 40-200Nm (with changeable head, ratchet, open ends, box ends) | 1
1 | |
| Adapter 1/2"-drive internal, 3/8"-drive external | 1 | |
| Adapter 3/8"-drive internal, 1/2"-drive external | 1 | |
| Extensions 1/2"-drive
Approximate length 50, 75, 120, 250, 500mm
Extensions 3/8"-drive
Approximate length 75, 120, 245mm
Extensions 1/4"-drive
Approximate length 250mm | 1 of each
1 of each
1 | |
| Extension-Friction Ball 1/2"-drive
Approximate length 50, 120, 250mm
Extension-Friction Ball 3/8"-drive
Approximate length 75, 145, 245mm | 1 of each
1 of each | |
| Socket set 1/4"-drive | 1 | |
| Deep impact socket 1/2"-drive 19, 21mm | 1 | |
| Universal socket 3/8"-drive, 10→19mm | 1 of each | |
| 6-point Socket 1/2"-drive, 10→22, 24→30, 32, 34, 36mm
6-point Socket 3/8"-drive, 7→14mm | 1 of each
1 of each | |
| 12-point deep socket 3/8"-drive, 10→17mm | 1 of each | |
| Spark plug socket 3/8"-drive 16, 21mm Magnetic or rubber holder | 1 of each | |
| Impact universal joint, 1/2" & 3/8"-drive | 1 of each | |
| Socket 3/8"-drive, hex5→8, 10mm | 1 of each | |
| Magnetic High performance bits holder socket, 3/8"-drive | 1 | |
| Socket external Torx®, 3/8"-drive T15, T20, T25, T27, T30, T40, T45, T50, T55 | 1 of each | |
| Screwdriver, 2.5mm flat tip
Screwdriver, 4.0mm flat tip
Screwdriver, 5.5mm flat tip
Screwdriver, 8.0mm flat tip | 1
1
1
1 | |
| Flexible nut driver 6mm
Flexible nut driver 7mm | 1
1 | |
| Nut driver 8mm
Nut driver 10mm | 1
1 | |
| Torx screwdriver T10, T15, T20, T25, T27, T30 | 1 of each | |
| Torx screwdriver T4-T9 | 1 of each | |
| Screwdriver, magnetic 1/4" bit holder | 1 | |
| Screwdriver, stubby magnetic 1/4" bit holder | 1 | |
| Bits ratchet, 1/4-drive | 1 | |
| Torx® Bit Kit, 1/4"-drive (short/long model)
Note! Must include Tx27 Phillips® Bit kit, 1/4"-drive (short/long model) Flat Tip Bit kit, 1/4"-drive | 1
1
1 | |
| Scissors | 1 | |
| Nut pliers | 1 | |
| Combination pliers | 1 | |
| Needle nose pliers | 1 | |
| Needle nose pliers, 45° angle jaw | 1 | |
| Universal pliers, small & medium | 1 of each | |
| Side cutter small & large | 1 of each | |
| Hose Pinching Pliers | 2 | |
| 9512619 | Pincers (double end) | 1 | |
| Pliers for bulbs | 1 | |
| Clip remover | 1 | |
| Utility knife with snap off points | 1 | |
| Knife | 1 | |
| 9814071 | Trim pad tool | 1 | |
| Blade Scraper
Extra blade | 1
1 | |
| File, mill type (for rough filing on brake callipers) | 1 | |
| File round, medium.
Approximately 8mm of diameter | 1 | |
| Multi-Cut flat file (second) Length.6"-8" | 1 | |
| Plastic mallet Approximate weight 300gr | 1 | |
| Cirve cross pein hammer Approximate weight 300gr | 1 | |
| Drift punch diameter 3→6, 8mm
Drift punch diameter 4mm, extra long
Drift punch diameter 6mm, extra long | 1 of each
1
1 | |
| Flat cold chisel Approximate length 120, 200mm | 1 of each | |
| Centre Punch (large) | 1 | |
| Automatic centre punch | 1 | |
| Putty Knife/scraper (steel) | 1 | |
| Pry bar
Length 400-500mm | 1 | |
| Tape measure 2m | 1 | |
| Feeler Gauge 0.05-1.0mm | 1 | |
| Vernier calliper | 1 | |
| Gauge, Tread Depth | 1 | |
| Air impact wrench, 1/2"-drive | 1 | |
| Air Ratchet, 3/8"-drive short model | 1 | |
| Airgun | 1 | |
| Cordless Screwdriver 1/4" slip chuck
Extra battery (Cordless Screwdriver) | 1 | |
| | | |
| Ear Protectors | 1 | |
| Safety glasses | 1 | |
| Oil can | 1 | |
| Wire brush | 1 | |
| Torch | 1 | |
| Telescopic/flexible mirror | 1 | |
| Magnetic pick-up rod, telescope type | 1 | |
Оно вам точно надо?
